Current car gets cutting tool

  • Time:
  • Click:132
  • source:CLAREY CNC Machining
The unique cutting tool system that develops by the company of Boehlerit of material cutting center of Austrian LMT group changed ISO turning range. Because used cutting tool of general Penta Tec to replace cutting tool of 5 kinds of ISO, dispense with the time that changes a knife for many times and time of cutting tool idle stroke, when applying on turning center, handling time shortened about 30% . 20 centuries 60 time, boehlerit of material cutting center invented dislocation type razor blade; 70 time, time of;80 of razor blade of hair palpability coating developed form of complex the chamfer that discharge bits (also call tenon tongue at first board) ; 90 time, optimized cutting tool cut dot and detached point. Begin, always undertake transforming in onefold treatment section, optimized ISO turning cutting tool, milling cutting tool and bore cutting tool later. In the last few years, boehlerit developed turning further again, auger cut and Chen Kongxi cuts cutting tool. This cutting tool applies to 5 kinds of cutting to process an operation, and also can replace cutting tool of 5 kinds of cutting, penta Tec of its commodity name originates namely the 5(Penta) of Greek. Penta Tec is one kind can perpendicular the cutting tool that uses with circumgyrate, accordingly, can use on lathe, drilling machine and milling machine. In the lathe that contains actuating device Penta Tec cutting tool perhaps is used on turning center, can save the space that institute of a lot of the plant that change a knife take up, assured the economy of treatment. Accordingly, leave out a lot of nonproductive cutting tool change time and time of cutting tool idle stroke, shortened thereby total handling time. Next, the bit of triangular dislocation type that takes 3 cutting blade as a result of what used economy, improved productivity. Cutting tool of use Penta Tec can undertake the following 5 kinds of cutting process an operation: 1.

Turning end panel is CK 45 when cutting material when, turn in every feed F is 0.

Ap of deepness of 15mm, cutting falls for the circumstance of 2mm, will achieve first-rate cutting result. Here, also can use for example PWLNR/L or PCLNR/L clamping apparatus of a kind ISO circumgyrate type. 2.

Even if express face turning to be in outwards even if turning is outward when the surface, use the Penta Tec cutting tool that contains WCHX 10T304 EN of 3 cutting blade, turn in every feed F is 0.

05mm, 0.

25mm, cutting deepness Ap falls for the case of 1mm, 5mm, can obtain first-rate to break bits result. Here, also can use for example PWLNR/L or PCLNR/L clamping apparatus of a kind ISO circumgyrate type. Regard other as option, the cutting tool that takes deputy cutting blade can 30 ° mix milling of 60 ° pour arris. 3.

Get in cutting via to be machined in this kind of cutting, penta Tec showed general turning, auger cut the puissant fabricating characteristics with unique cutting tool. Be based on the special structure design of cutting tool forehead, with triangular dislocation razor blade union is used, penta Tec can be accomplished need not make nap can undertake reaming to the via of prior operation again, thereby dispense with need with other method additional the treatment operation of cutting tool and other. Another characteristic of this kind of cutting tool is already can perpendicular use, can use in circumgyrate again. Next, the cutting tool when machining via can 1mm of deviate aperture center, so, can get cut with cutting tool diameter the relation is D × 1.

The aperture of 1. Below the case that getting via especially, can obtain cooling fluid, so Penta Tec always can make sure first-rate discharges bits effect. In drilling operation, penta Tec can replace broach and handle type milling cutter at least. 4.

The surface inside fore-and-aft turning is hanged in cutting tool extend a capacity to 2.

Below the circumstance of 25 × D, this kind of cutting tool has the advantage that suits the surface inside treatment. Have the aid of at spray orifice of the cooling fluid on cutting tool, make Penta Tec is in all sorts of inside have in exterior treatment on the effect discharging bits of beautiful. Additional, have the aid of is mixed at the big clamp diameter on flange additional end panel device, the stability that makes this cutting tool compares ISO drill pipe should be gotten high much. In this kind operation circumstance falls, also can use like A PWLNR/L a kind ISO drill pipe. The deputy cutting blade of usable Penta Tec is in of workpiece inside the surface pours arris. 5.

All of diameter of cutting tool of heavy aperture milling has set according to DIN 74. Cutting tool diameter is 10mm, 15mm, 18mm and 20mm. Once the heavy aperture of hole of sexual treatment pearl eye gets the range offerring money that expanding in preparation first. Can be in milling machine, machining center or in economy model, this kind of cutting comes true to process an operation on the lathe that contains cutting tool actuating device. Penta Tec applies to all machine tools. The handling time of milling cutter cutting that the 5th cutting tool can replace heavy aperture treatment to use decreases about 30% . The cutting tool on in order to is replaceable cutting tool of 5 kinds of ISO, make the handling time on turning center, decreased because of saving the time that change a knife and time of cutting tool idle stroke about 30% . CNC Milling