The stage amounts to transducer parameter

  • Time:
  • Click:294
  • source:CLAREY CNC Machining
The stage amounts to series of three-phase of 230VAC of   of   of   of   of   of transducer A series: Standard of A007022037055075110150185220 of □ of □ of model VFD □ is applicable and motor output power (KW) 0.

751.

52.

23.

75.

57.

5111518.

522 the biggest applicable motor output power (HP)12357.

51015202530 output nominal capacity (KVA)1.

92.

73.

86.

59.

512.

517.

522.

828.

633.

2 output are rated electric current (A)5.

07.

Limits of 01017253346607587 output frequency 0.

1Hz-400Hz/0.

Electric current of output of 150%ED of 1-1500Hz overload ability runs 60 seconds correspondence of voltage of the biggest output inputs number of power source photograph.

Voltage.

Frequency is single-phase / three-phase three-phase 200-240Vac, 50/60Hz voltage.

Frequency allows fluctuant limits voltage: ± 10% , frequency: ± 5% inputs electric current (A)11/7.

415/1027/1519.

633.

543.

346768399 refrigeration come loose hot system is compulsive series of three-phase of 460VAC of   of   of   of   of   of   of   of   of   of   of   of   of   of wind cold   : Standard of A007015022037055075110150185220 of □ of □ of model VFD □ is applicable and motor output power (KW) 0.

751.

52.

23.

75.

57.

5111518.

522 the biggest applicable motor output power (HP)12357.

51015202530 output nominal capacity (Kva)2.

33.

13.

86.

29.

913.

718.

524.

428.

934.

3 output are rated electric current (A)3.

04.

05.

08.

Limits of 2131824323845 output frequency 0.

1Hz-400Hz/0.

Electric current of output of 150%ED of 1-1500Hz overload ability runs 60 seconds correspondence of voltage of the biggest output inputs number of power source photograph.

Voltage.

Frequency three-phase 380-480Vac, 50/60Hz voltage.

Frequency allows fluctuant limits voltage: ± 10% , frequency: ± 5% inputs electric current (A) 4.

25.

77.

08.

51420.

628303949 refrigeration come loose hot system is compulsive wind cold function is characteristic: Means of PWM of Zheng Xuanbo of means of control character control (V/F is controlled) output frequency limits 0.

1Hz~400Hz(H series can amount to resolution of 1500Hz) frequency set 0.

1Hz outputs frequency resolution 0.

Frequency of 1HzPWM carrier wave can adjust torsion to promote automatic torsion promotion and automatic slippery poor compensation from 3kHz~15kHz, the torsion that start can amount to the rated torsion of 150% to prohibit when 5Hz set frequency was quickened at 3 o'clock / slowdown time 0.

1~600 second (add slowdown time two kinds to be able to become independent respectively set) stall prevents to follow a basis motor load performance when with driver the 50~200% set d.c.braking of rated electric current stops but from 0.

1~60Hz operation, the rated electric current of restraint current 0-100% starts time 0-5 second, second of stopping time 0-25 picks up the resistor of apply the brake that torsion of apply the brake receives a choose and buy outside 20%(about can amount to 125%) , 1-10HP brake is installed inside electric crystal, 15-30HP but outside receive unit of apply the brake curve of V/F of set of random of curve of modular group V/F operates signal of characteristic frequency set digital position operator is bolted by ▲ ▼ set is exterior terminal 0-10Vdc, 4-20mA, signal of operation of movement of RS485 communication interface is digital position operator can carry out outside terminal by key of RUN, STOP, JOG 2 lines are made / 3 lines make movement, inch use movement, terminal of RS485 communication wisdom input can set speed switch 8 paragraphs beforehand, 1, 2 add slowdown time switch, add decelerate to prohibit, exterior suspend output, inch use movement, increase by degrees / set of degressive frequency terminal, movement of terminal of exterior tally wisdom output is indicated, frequency arrives at output, 0 fast directives, computation arrives at output, cross torsion output, exterior interrupt a directive, low voltage check goes out, handle mode instruction, breakdown directive, exterior and unusual interrupt analogy signal to output correspondence to output frequency or contact of fault signal of output electric current actually relay of a NO/NC contact or open collector 2 times to output built-in function to output frequency High/Low to be restricted set, restart of instantaneous power cut, unusual breakdown restart, s curve, automatic stabilized voltage adjusts AVR, unusual record, parameter lock reachs replacement surely, REV prohibits, cross voltaic stall to prevent, overvoltage stall prevents, the electron heats up the post that use phone, energy-saving movement, adjust automatically add slowdown time to protect functional overvoltage, pass electricity, low voltage, exterior and unusual interrupt, electric machinery overload, ground connection breakdown, driver overload, digital position operator contains driver overheat 8 function key, the monitor of 7 paragraphs of LED of 5 digit, 5LEDs condition is indicated, but set frequency F, output frequency H actually, output voltaic A, the person that use defines parameter READ/WRITE oneself, breakdown information shows, RUN, STOP/RESET, FWD/REV, inch temperature of environment of operation of condition of condition of the swivel that use motion - 10 ℃ To +40 ℃ (the dew that do not have a knot, knot freezes) store temperature - 20 ℃ To +60 does not have a knot under 90%RH of humidity of ℃ operation environment 1000m of dew installation height is the following, without vibration of caustic gas, liquid, dust 20Hz is the following 9.

80665m/s2(1G) , 20~50Hz5.

88m/s2(0.

6G) CNC Milling